Beeswax Foundation Mould Press - Wax Printer

Manual press for hommaking of comb foundations, with simple pouring of wax and pressing you can make comb foundation.

 

beeswax foundation mould press

All stainless steel construction including hinges and hidden matrix, with silicone rubber cell formers. Cell sizes for apis mellifera mellifera (5.4mm wide) and apis mellifera scutellata (4.7mm wide) available. Makes sheets 420 x 245mm deep when closed. Suitable for British Standard, Commercial or Langstroth hives only.

Instructions for Use

1. Fill a large sink or other container with cold water
2. Place the hinged edge of the Press flat on a firm surface and slightly open the Press
3. Pour in the liquid wax until nearly full and squeeze shut, pouring away the excess wax
4. Put the Press into the water. After only 2-3 seconds, carefully open the Press underwater and remove the sheet of wax. This will need to be trimmed to the correct size.
5. Remove the Press from the water and stand it open on its edges to allow water to run off.
6. Give the Press a gentle rub with a kitchen towel to break up any water droplets. Alternatively the water could be made up of a soapy solution of washingup liquid which will prevent water droplets forming.

This version of foundation making press called a "Beeswax Foundation Mould" was manufactured by the KingReal company.. The matrix impression plates are made by electro-deposition of copper on to wax 'master' sheets that had been sprayed with an electrically conductive paint.

This method of casting beeswax foundation produces fine quality sheets of home made foundation that are slightly more brittle than foundation produced by the milling process. This brittleness is increased if the sheets are exposed to freezing temperatures, even after the temperature is returned to normal.

wax foundation mold press

Equipment Required

  1. Double boiler (e.g. a bowl floating in a pan of water) in which to melt the beeswax.
  2. Mug or ladle for pouring molten beeswax (DO NOT USE copper, brass, or iron - These discolour and harm wax) (A plastic mug or jug is inexpensive and does not cool the wax too much).
  3. Board or metal sheet of the size required as a template for finished sheets. (make this template slightly large to allow for shrinkage)
  4. Knife or Pizza Cutter to cut around the template.
  5. Release agent (e.g. rain water with a drop of liquid detergent two or three percent of alcohol and a spoonful of honey and/or a dash of lemon or lime juice may also be added if required).

 

Process

To prepare the mould before using for the first time :-

  1. Wet both the mould dies with release agent.
  2. Pour very small cupful of liquid detergent (washing up liquid) on to each part of the mould.
  3. Scrub very gently with small nylon brush all over both mould plates and the wooden surround.
  4. Rinse off the detergent using release agent.

Making Foundation

  1. Pour in approximately 500 ml of release agent to thoroughly wet both mould plates and the wooden surround.
  2. Close the mould to ensure even wetting. Then open a little and pour the release agent back into it's storage pot.
  3. Before the release agent dries pour in the molten beeswax to cover base of mould. Close lid of mould quickly, but gently.
  4. Pour the excess wax back into wax pot.
  5. Leave the mould until the wax has cooled to a firm, but cheesy solid - (perhaps one to two minutes is suggested in the Steele & Brodie leaflet, but I find 30 seconds is enough.) There should be enough time to trim the previous sheet to size as in step ( I ).
  6. Open the mould. The solid sheet should stick to one side of the mould - usually the top.
  7. Trim the excess wax from the two sides and top (using a blunt knife). Use the bottom edge to pull the sheet away from the mould (start at one corner).
  8. Discard and re-melt the first few uneven sheets (caused by the mould warming up to the optimum operating temperature).
  9. Allow the fresh sheet to cool for two to three minutes (for most of the shrinkage to take place). Place the foundation on a flat surface. Then using the template and knife (or pizza cutter), cut the sheet to the size required. Off cuts and unsatisfactory sheets can be returned to the molten wax reservoir (this helps to maintain the melt at just the melting point of the wax).

 

Fire Danger...

TAKE CARE - BEESWAX IS FLAMMABLE. Never place beeswax on direct heat (e.g. open fire, gas stove, boiling ring etc.) Always use a double boiler or water bath.

If the wax sticks to the mould

  1. Pour on COLD release agent to loosen wax.
  2. If still sticking, pour hot (not boiling) rain water over the wax to melt it away. Scrub with a small nylon brush and liquid detergent to remove remaining wax. Use a sharpened wooden stick to pick off small pieces of wax.

NEVER use sharp tools or a wire brush to clean this mould. The mould plates are made from electro - formed copper. If they are marked or damaged in any way... All sheets cast will also be marked and damaged. TAKE CARE.

After continuous use, the release agent will get hot and slow down the setting time. Replace with cold solution and keep topping up the wax melting pot with solid wax to keep the temperature at only just above the wax melting point.

Much of this text has been taken from a leaflet, produced by Steele & Brodie, that was included with the press when they were sold. Many of the comments on the Herring page are also valid when making foundation using this type of press.

Try for as high an ambient temperature as possible along with as low a wax temperature as can be achieved. If the mould is really stuck shut, do not use excessive force, but allow to cool for 24 hours in a deep freeze.

 


Copyright © 2008-2014 Changge KingReal Beekeeping Supplies Factory All rights reserved.
Address: NO.199 Shuang Miao Li, Dazhou Town, Changge City, Henan Province 461507, China PR.
Email: tanjie2004@gmail.com tanjie@beekeeping-tools.com
Tel:86-1861 0083 868